Up to 128G. A 64G memory card is included in the package. 

Dear Customer, Thank you for your question. Please check the following steps to setting the focus: (Do not look at too close objects) Step 1. Cover the right objective lens with your hand or close your right eye, rotate the central independent focusing wheel until the image in the left eyepiece is sharp and clear. Step 2. Now cover the left objective lens or close your left eye, rotate the right eyepiece focusing wheel to adjust the diopter of the right eye until the captured image is sharp. 

Step 1: Being careful not to touch the lens, cover the right objective lens (or close your right eye) and turn the central focusing dial until the image seen by the left eye is clear. Step 2: Cover the left lens (or close the left eye) and this time instead of turning the central focusing wheel, turn the diopter adjustment ring (located near the right eyepiece and displayed on the small image in the upper right) until the image is clear. Step 3: Finally look through the binoculars with both eyes until the image is clear and sharp. 

Everything affects the signal. I can mount mine over a window and get one set of channels. Then move it 12” and get twenty additional channels. It’s a good antenna. I encourage you to get it and try it in several positions. I will add the double sided tape they send won’t hold the antenna for more than a couple of days. You’ll need something else. 

If your camera indicated "lens is not properly installed", please modify the camera menu settings. Usually called the "release the shutter the lens is not installed", you can modify the settings to allow. Specifically refer to the camera manual.Following are some examples:

1. MFT（M4/3 mount camera）'Lens Not Found' - Warning Message Appears
   For Panasonic Lumix:
   The camera needs to be set to function without a MFT-Mount lens attached. You can do this by changing the following camera setting:
   'Menu' -> 'Custom Menu 5' -> 'Shoot W/O Lens' -> 'On'
   (Exact naming and location of this option may change depending on camera model)
   
2. Fujifilm X mount camera, The camera needs to be set to function without a GFX-Mount lens attached. You can do this by changing the following camera setting:
   'MENU' -> 'SETUP' -> 'BUTTON/DIAL SETTING' -> 'SHOOT WITHOUT LENS' -> 'ON' (Exact naming and location of this option may change depending on camera model) Choose ON to enable the shutter release when no lens is attached.
   
3. Sony E mount camera, 'No Lens Attached' - Warning Message Appears
   The camera needs to be set to function without a E-Mount lens attached. You can do this by changing the following camera setting:'Menu' -> 'Setup' -> 'Release w/o Lens' -> 'Enable'
   (Exact naming and location of this option may change depending on camera model)
   
4. Nikon 1-Series mirrorless camera , 'Check lens. Pictures can only be taken when a lens is attached' - Warning Message Appears
   With a Nikon 1-Series camera (such as the J2), you will need to make sure the camera is in 'Manual' exposure or shooting mode and the focus selection is also set to manual. When in any other mode the camera tries to take control of the lens which is not possible as the adapter does not have any contact with the camera circuitry, so you get the lens check warning as the camera does not think there is a lens attached.
   
5. 'EOS M mirrorless camera ,'No Lens Attached' - Warning Message Appears
   The camera needs to be set to function without a EF-M Mount lens attached. You can do this by changing the following camera setting:
   'Menu' -> 'Custom Menu' -> 'Custom Function 7' -> Select 'Release shutter w/o lens'
   (Exact naming and location of this option may change depending on camera model)
   
6. Konica Minolta:
   For Konica Minolta and "No Lens Attached"
   Custom Menu 3
   First item "Shutter Lock"
   Set it to "Off: no lens"
   (Depending on camera model "Shutter Lock" May be in different menu location)
   
7. 'Samsung NX 'No lens.' - Warning Message Appears
   The adapter is designed to trigger a sensor inside the camera body itself so no setting needs to be changed. If the error message is coming up with one of our adapters attached, then it is possible that the adapter is not hitting that sensor the way that it should. Usually rotating the adapter slightly in the mount, or un-mounting and remounting the adapter clears the problem with no further action needed. If that doesn't solve the problem, then the best course of action would be to swap out the adapter you have with a replacement.